Be ready programmers, new update for the WPLSoft!
Many new stuff added on that new version, program password protection (on the PC), Float type on the edit register memory, new SE added on the PLC list, and many other thinks that you can check on the announcement below
Technical announement WPLSoft v2.30
Warning! the DVP format has change! so the previous WPLSoft can not open the programs saved on WPLSoft 2.30.
As always the software is for free, and you can download it on Delta website or our FTP site.
Delta Website Delta PLC Software
FTP Site Delta PLC Software
name: den-eindhoven
Password: BuPd2175
Just for your information, be aware that other Delta software has been update this month. VFDSoftv1.46 and DCISoftv1.08.
And pretty soon ISPSoft will be update too.
Don´t hesitate to let us know your thoughts
Delta Industrial Automation 
August 19, 2018 at 3:28 pm
i am using wlpsoft programme c200 for counter ,hmi display ok..but power fail reset become zero how to save & continue after power restore.
November 11, 2017 at 5:01 am
hi i need help
i created programme @wlpsoft and it is run ok but some output didn’t carry out unless delete some network…
February 26, 2017 at 6:24 pm
i have wplsoft 2.4.1 while simulation i am facing timeout problem and my simulation is not working please guide me..how can i remove this problem..
December 23, 2021 at 4:40 pm
Did you find any solution for this,I am still facing this problem so please help me if you know
December 8, 2015 at 1:30 pm
Hello ,,
I use DVP 64EH
I,m new in plc
there are problem I can’t run most of input when I run it this message appear
(the device address is over the range connected model)
can you help me
January 19, 2015 at 8:13 am
hi i m using ES2 series plc, problem is that after power failure some SET bit remain set after RESET comand and process cycle run with some missing steps. All set bit are NON laching and all have RST bit with one input signal .when re-download same ladder its work fine……i miss any power up bit or other?????
September 8, 2014 at 9:50 am
hello
how can i change the comport in wplsoft ?
June 18, 2014 at 10:28 am
hi this is bhavin
i want to use “hp laserjet 1020 plus” printer to print from hmi “dop-b07s415”
but i can’t able to do … so can delta electronics add this printer in dop-b series hmi please? please reply as soon as possible
June 18, 2014 at 2:55 pm
Use pictbridge compatible printers please.
June 19, 2014 at 10:12 am
Dear Sir…there is low range in this pictbridge compatible printer and available printer with this technology is not set in budget so is there any other option to use hp laserjet 1020 plus printer ?
please reply as soon as possible
thank you.
July 12, 2014 at 8:31 am
HELLO SIR,
CAN I USE EPSON LQ-300+ ii AFTER SELECTING LQ-300+ IN DOP-B07S415?
PLEASE REPLY AS SOON AS POSSIBLE
THANK YOU.
November 2, 2013 at 9:42 am
DEAR Sir I have just downloaded the WPL-Soft v2.35 but there is a problem in it when i try to run the program in offline simulation the software displays a timeout message. please help
November 14, 2015 at 3:50 pm
Same problem I am also facing pls help
February 26, 2017 at 6:28 pm
murtaza do you got the solution if so please tell me i am facing same problem.
September 20, 2013 at 1:27 pm
how we can run wplsoft from limted user account.
July 16, 2013 at 7:36 am
sir,iam using delta plc dvp-20ex if i give x0 as address the program is working form control pannel but from software if i ON it; It shows ” DEVICE ADDRESS OUT OF RANGE FOR THE CONNECTED MODEL (CODE-2)” PLEASE GIVE SOLUTION
July 9, 2014 at 8:13 am
HI
I had the same problem..you can not turn on your input from the software (x0) ,in softeware you have to use memory instead and turn the memory on( m0) . you can just turn the input on from your hardware..
October 14, 2016 at 5:06 am
I am also facing same problem while using DVP12SA2. can anybody help??
December 17, 2016 at 9:53 am
Just check model selection . I mean PLC type.
May 17, 2013 at 11:19 am
Hello!
Installation of DCISoft v1.08 under Windows 7 x64 Enterprise always ends with error “CallClassInstaller(REGISTERDEVICE) FAILURE: (0xe0000235)”.
When running after installation it finds my DVPEN01-SL module but stops working while trying to save config to dci-file with Error “Delta Communication Integrator has stopped working…”
I’ve tried this on several PC with Win7 x64 with the same result.
What could it be?
On the official site support of Win7 x64 is declared.
http://www.delta.com.tw/product/em/download/download_main.asp?act=3&pid=3&cid=1&tpid=3
Thank you!
November 23, 2012 at 8:38 am
hi there
i use wpl2.30 for upload program but they have message : comm eror (function does not support)
what is happened to these.
September 20, 2012 at 4:55 pm
Hello to everyone in the group would like to help in Delta PLC programming.
I need a cyclic state for when input X0 is triggered, the output Y0 be teetering league one second is one second off looks like this forever. A sort of wink wink.
Robson
September 21, 2012 at 1:18 pm
Try with M1013
September 20, 2012 at 3:20 pm
Hello out there, i’m a beginner in PLC, i would like to ask how to read data from a database(barcode tht is created in MS Access) using WPLSoft?
my program is something like this:
when an item is scanned, the plc read the scanned barcode and energized an output.
Any tutorial for it? Thank you.
July 18, 2012 at 5:08 am
When I install 2.3 some of the wizards are missing. The PID, High Speed Pulse count, Pulse output etc.
What is happened to these.
June 28, 2012 at 2:27 pm
Unfortunately I tried the newest upgraded version V.30 with disastrous results. I had to go back to V2.20. It inhibited my com port (Windows 7)
June 7, 2012 at 6:11 pm
Due the new coding for v2.30 some of the wizards needs to be redesigned.
In this moments our engineers are working with them.
It will be available in following version for shure, as soon as I got schedule I´ll publish on the post.
Thanks for coment and sorry for inconveniences
June 6, 2012 at 7:51 am
HI THIS IS BHAVIN
I HAVE DOWNLOAD THE “WPL SOFT V2.30”
I IS GOOD BUT I MISSING ONE FUNCTIONALITY FOR “ANALOG EXENTION MODULE” NAMED: “AUXILARIY SETUP FOR EXENTION MODULE” WHICH IS AVAILABLE IN PREVIOUS VERSION WPL SOFT 2.20.
SO IF IT POSSIBLE THEN IMPROVE THE NEW VERSION WITH THIS FUNCTION PLEASE.
THANK YOU.
June 5, 2012 at 11:19 am
is it possible to open segment to seperate windows and see segment list in tree view (like omron’s section and section project tree). we can easly read and modificate long programs
June 5, 2012 at 11:23 am
Hello metin,
For long programs I recommend ISPSoft, in this case, you can open sub programs end edit them separately from the main program.
https://deltautomation.wordpress.com/2011/07/11/announcement-ispsoft-1-03/
June 5, 2012 at 11:44 am
yes i know and already try ispsoft, maybe for new projects i can start from beginning with ispsoft, but i already have lots of programs and i don’t want to convert them to isp. “if its works, dont touch” some old habits :)
June 5, 2012 at 11:47 am
Good habit indeed!! ;)
In this case I´afraid is not possible.
But I´ll send your idea to R&D for further versions.
Thanks for good feedback!